![]() Via a Basilisk script as described in the BSK Scripting Settings. The basic user interface elements of Vizard. Heliocentric trajectory it is shown, also enlarged, in this view.ĭouble clicking on a planet returns the user to a planet-centric The planets are drawn enlarged to make them visible, and the planet Heliocentric View Mode: Here a solar system wide view is shown. To return to a spacecraft-centric view modeĭouble click on the spacecraft. The spacecraft is drawn at an exaggerated size so it is visible as aģD object in this view. When rotating the view point this is about with the center of the ![]() Planet-Centric View Mode: Here a planet-wide view is presented. Out locally, but if you zoom out too far then the view mode switched Spacecraft trajectory is not shown in this view. Rotating the center of the spacecraft is the center of rotation. Spacecraft-Centric View Mode (default): Here the spacecraft isĭrawn 1:1 while showing other celestial objects about it. View point can be rotated and the user can zoom in and out. This can be either a host name or an IP address. Network address to use for the connection. Transport protocol to use for the connection. This example would cause Basilisk to use the socket address tcp://127.0.0.1:1234 to connect to Vizard. Just repeat the steps to install the OS, but instead of clicking on “Installer,” click on “Install System Software,” select “custom install” and click the check-boxes beside the components you need under “networking and connectivity.”įigure four: Configuring the TCP/IP Control Panel.Viz = vizInterface. You can easily install them, if you have the System 7.5.3 system setup files from the earlier guide. NOTE: If you don't have “Apple Extras,” “Network Software Selector” or “TCP/IP” it is because they were not installed when System 7 was set up. Six: In “Name Server Addr” enter the DNS address you noted earlier. One: Select “connect via Ethernet” (this should be the default setting)įour: In “Subnet Mask” enter 255.255.255.0įive: In “Router Address” enter 192.168.0.1 If you get a prompt about TCP/IP being inactive, click “yes.”įollow these steps to set up your Internet access: Double click on the “TCP/IP” control Panel. Open the System Folder and the Control Panels folder. Close the Network Software Selector.įigure three: Open the Network Software Selector in the “Apple Extras” folder and select “Use Open Transport Networking.” Double click on the icon called “Network Software Selector” and select “Use Open Transport Networking” (see Figure three). Open the folder “Apple Extras” on your system disk. At the prompt type “ipconfig /all” and make a note of the DNS Server address (see figure two).įigure two: Make a note of your DNS address Setting up Internetīoot your emulated Macintosh. In the Windows Start Menu, select “Run…” and type “cmd” to open a command prompt. Now close the GUI.įigure one: Adjusting Graphics settings in the Basilisk II GUIīefore you can set up internet within the emulated Mac, you need to know your DNS address. In the Graphics and Sound tab, change the Windows refresh rate to “Dynamic” (this will make your mouse movement smoother) and change the width and height settings to either 1024 * 768 or to “Maximum” (this will run the emulator in a larger window). ![]() ![]() In the Memory/Misc tab, change “MacOS RAM Size” to 32 or more. If you haven't already made them, there are a few settings that should be changed from the default to ensure pleasant web browsing. First, open the GUI and in the Network tab under “Ethernet Interface,” select “Basilisk II Router.” You must make a few adjustments in the Basilisk II GUI before getting online. As before, click “ok” at the “select copy mode” prompt. Use HFV Explorer to do this, in the same manner described in the Basilisk II setup guide. Start by copying the iCab archive over to your Macintosh disk image. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |